Three tires were at 40ish psi (fine) and one was at 75 psi. Search Car Torque Specifications by Engine or Model. When I got home I confirmed pressures before sticking them in the garage. I brought my OEM Audi S3 wheels to Mavis Tire the other day to have the winter tires switched back to the stock PZeros in preparation for lease end. From door panel specs to engine head torque values we have it all listed for you. If you’re like me, I even forget what the basic oil drain plug and filter housing torque specs are.
Use this guide as a cheat sheet for all the torque values for your E46 M3. If they're way too tight, they will stretch the threads, also leading to failure. Ultimate BMW E46 M3 Torque Spec Guide Buildjournal. I would try not to worry about it, but lug torque values are set for a reason-if they're too loose, they will move more and more over time and eventually allow wheel movement on the hub, potentially causing a wheel to come off at speed. Data is provided in Newton meters (Nm), meter kilopond (mkp), and pound foot (lb.ft).
Bmw torque specs wheels manual#
For your convenience all the specs have been compiled technical manual and sorted as it would be in the BMW 2002 Service Repair Manual. I've come home from the dealer with four bolts on one wheel impacted down way too tight, and the fifth bolt on that wheel not even finger tight to the hub. It is imperative to use proper torque on all of the bolts on your car. All F-Chassis use the 105ft-lb torque spec, spacers or without spacers. And yet they routinely overtighten or undertighten lugs after doing wheel or brake service. The difference is due to the F-chassis BMWs using a larger lug shank (14mm vs 12mm).
I pay them to be the experts and do the right thing. I trust shops to know more than I do when it comes to this stuff. They probably won’t fall off at 80 either, who knows why they changed the spec slightly. I tighten mine 10% over the spec because my wrench is cheap and rather be a little over than under.
Seriously, though, let me know what he says, in return I will call a couple other dealers in SoCal, and let you know what they say.Judging by the number of shops that tighten them to 9999 ft-lb with an impact gun, I’d say you’re fine exceeding 100 as long as you can get them off and you’ve tightened them in a star pattern and equally. I'm with you, now that you mention it that did bother me when I first changed the wheel locks, but I since put it out of my mind. multiple power take-up elements including the torque converter, the hybrid drive. So I asked the SA, and that's what I went with. but also flexible because of hybrid and all-wheel compatibility. I don't know what M12, or M14 was in reference to. I got confused by the exact same thing, when I bought the wheel locks. I get a bit anal about things like torque settings and tyre pressures, so I'll call my local dealer in the morning and see what they come up with - I'll let you know. Going by that, 90 Ft/Lbs doesn't reach the lower end of the tolerance band.
Bmw torque specs wheels plus#
BMW F30 Wheel Bearing Torque Specs: BMW Wheel Bearing Bolts 80Nm or 59 ft-lbs, of torque BMW Axle Bolt 210Nm or 155 ft-lbs, of torque, plus 90° Youre much better off now that your wheel bearing is fresh and ready for another 100,000+ miles.
Bmw torque specs wheels series#
It's a general leaflet catering for most models including 3 and 5 series and it's issued by BMW.įor reference 120 Nm = 88.5 Ft/Lbs, 140 Nm = 103 Ft/Lbs. In fact, the car is eager to spin up its rear wheels even in third gear due to the huge horsepower and torque figures. Lastly, refit the wheels and thread in the lug bolts before tightening them with a 17mm socket. Since posting the question I checked the instruction leaflet that was included in the BMW locking lug nut pack for my E92.
Not only is it a pain to get them back off when needed, but overtorquing can also strip the lugs and warp your rotors. Unfortunately, a very common occurrence for techs to just gorilla the lugs back on using the air gun. Thanks guys, but there seems to be an element of confusion here. iTrader: ( 0) Yep-it's 88.5 ft-lbs or 120 N-m of torque.
0 kommentar(er)
